The “F1” error means that the dryer’s thermistor failed. The dryer is reading the thermistor as “open” and the actual part has shorted out. The thermistor is used to read and control temperatures within the dryer. Without the part, the dryer will not operate.

How do I fix F01 error?

The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse.

What does F 01 mean on Whirlpool dryer?

Dryer Repair. If your Whirlpool dryer is displaying an F01 error code, this means there is something wrong with the control board or one of the components connected to it. It is commonly caused by a power failure or after a power surge occurs.

What does F1 and e1 mean on a Whirlpool dryer?

A “F1E1” code in the display indicates there may be an issue with the control unit or the associated wiring. Touch POWER, select a cycle, then hold START/PAUSE button to start the dryer. If this is unsuccessful, unplug the dryer.

How do I reset my Duet dryer?

If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer. If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.

What does E1 F1 mean on Whirlpool washer?

The Whirlpool Washer F1E1 error means the ACU (main control board) memory is corrupted or another critical ACU failure has occurred. It’s possible that a power surge or a drop in voltage caused the issue. Unplug the washer for 1 minute and plug it back in.

How long should a dryer last?

A dryer should last 10-13 years. To extend the dryer’s life, clean the lint trap after each use and make sure the outer vent is clear as well.

How do I reset my Maytag EPIC z dryer?

Full Reset Disconnect the power to the Maytag dryer and wait 30 minutes. After 30 minutes, restore power and make a new selection. If the problem persists or the dryer will not operate, disconnect power once again and call Maytag for service.

Where is the thermal fuse on a Whirlpool Duet dryer?

Remove the back access panel on the dryer, and look for the exhaust duct near the bottom of the unit. The thermal fuse is either circular or oblong, often white plastic with black material in the center and two wire leads. The thermal fuse is mounted on the exhaust duct.

What does AF on my dryer mean?

An AF (Restricted Air Flow) error code indicates that the lint screen or house vent is clogged; the vent may be crushed, kinked or have too many turns. The dryer will continue to run when the is error is present. Touch any key to clear the code from the display and return to the estimated time remaining.

Article first time published on

What does F01 mean on a washing machine?

F01 — Electronic circuit board fault. Issue: Washing Machines is not operating – some or all functions are not selectable. Advice: We recommend you disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply and wait 30 seconds and try starting the machine again.

Where is the dryer reset button?

Many dryers are equipped with a reset button on the control panel.

Is it worth fixing a dryer?

Is it worth repairing a dryer? Dryer repairs are worth it if the appliance is less than 4 years old and the cost is less than $400. For older dryers and/or costly repairs, replacing your appliance is more cost effective.

How can you tell if your dryer is going out?

• Your Clothes Aren’t Drying Properly. Do you feel wet or damp areas when you remove your clothes from the dryer? …
• Excessive Noise. Do you often hear a lot of noise, such as rattling, banging, or high-pitched squealing? …
• It’s Too Old. …
• You See Exposed Wiring.

What does a new dryer cost?

The national average cost for dryer repair is $170. New dryers cost anywhere from $400 for entry-level to $2,000, or more, for top of the line. To save some money and save your dryer from the landfill, here’s the scoop on dryer repair cost.

What is F1 error on Whirlpool washer?

4 Answers. Usually, it’s a problem with the control board. By replacing the control board, you should be able to fix the problem. However, it might also be a problem with the hose, something might be stuck in the hose.

How do I fix E1 error on my Whirlpool washer?

1. Check that the water faucets are not closed.
2. Check that the water pressure in the house is over 20 kPa.
3. Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement.
4. Check that the drain hose is not below 27½” (700 mm) from the floor.

What does F1 code mean on Kenmore Elite dryer?

The “F1” error means that the dryer’s thermistor failed. The dryer is reading the thermistor as “open” and the actual part has shorted out. The thermistor is used to read and control temperatures within the dryer. Without the part, the dryer will not operate.

How do I know if my Whirlpool dryer thermal fuse is blown?

1. Unplug your dryer and ensure it is no longer connected to the gas or electric.
2. Locate the thermal fuse, as above.
3. Disconnect the thermal fuse from the wires.
4. Test the fuse with a multimeter.
5. If the needle on your multimeter does not move, your thermal fuse is blow.

How do I know if my thermal fuse is bad?

Multimeter Test Remove the two wire leads from the thermal fuse and touch a multitester probe to each wire terminal on the fuse. If you get a reading of infinity, the fuse is fine. Any reading less than infinity indicates a triggered thermal fuse you will need to replace.

What happens when thermal fuse blown on dryer?

A thermal fuse will blow when the temperature gets too high, not when it’s drawing too much current. … When it blows, the dryer stops generating heat. It’s necessary to replace it before the dryer will run again.

What does PF mean on my Maytag dryer?

A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure. Touch and hold START to restart the dryer cycle or press POWER to clear the display.

Why is my Maytag dryer not starting?

Blown thermal fuse: A thermal fuse will blow if the dryer is in danger of overheating or if the fuse is faulty. In either case, your Maytag dryer won’t start, just beeps, when you press the Start button. A blown or broken fuse can’t be repaired and must be replaced.

How do you unlock a Maytag dryer?

Press and hold the Control Lock Key for 3 seconds to unlock the machine. You will notice the machine count down from 3-2-1. The control lock may be a stand alone key, or it could be a dual function key paired with another button like Extra Rinse, Steam, etc.

Why is my Whirlpool dryer flashing AF?

The AF code (Air Flow) on a Cabrio Dryer is signaling that the machine does not have proper airflow. … The excessive lint inside the drum shows that the lint is not being drawn into your dryer filter because of the poor circulation of air.

What does PF mean on Whirlpool Cabrio dryer?

A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure. Touch and hold START to restart the dryer cycle or press POWER to clear the display.

How do I fix Hotpoint F01?

When your washer dryer shows error message F01, we advise you to disconnect and unplug your Hotpoint washer dryer from the mains supply for 3 minutes. After 3 minutes have passed, reconnect your Hotpoint washer dryer and wait 30 seconds before you start up the machine again.

What does F01 mean on a Hotpoint dryer?

F01 — Electronic circuit board fault. Issue: Tumble Dryers is not operating – some or all functions are not selectable. Advice: We recommend you disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply and wait 30 seconds and try starting the machine again.

What does F1 mean on Hotpoint washing machine?

F1 – Motor Triac Short. The motor triac controls the speed of your washing machine motor. If a fault with the triac, the triac connections or wiring or the motor has developed you’ll see this error.

Does unplugging a dryer reset it?

Resetting your dryer is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dryer (usually 1 to 5 minutes at most), and then power it up again. That’s it. That’s all it takes to reset.

Why won't my dryer start all of a sudden?

Common dryer issues include a faulty door switch or start switch and control problems such as a broken dryer timer or faulty electronic control board: … If the drum light doesn’t turn off, a failed door switch is the likely reason the dryer won’t start. A blown thermal fuse often prevents an electric dryer from starting.