The Aqua Genie is ingeniously designed to create currents that force surface debris toward the skimmer mechanism. As water is returned to the pool from the filter, it is forced downward by the Aqua Genie’s pressure chamber. … As a result, all the water in the pool is kept cleaner.

How does Aqua Genie work?

The Aqua Genie is ingeniously designed to create currents that force surface debris toward the skimmer mechanism. As water is returned to the pool from the filter, it is forced downward by the Aqua Genie’s pressure chamber. … As a result, all the water in the pool is kept cleaner.

How do you vacuum an inground pool with two skimmers?

When you vacuum a pool with more than one suction port, you need to close the others off. In your case with 2 skimmers, either shut the second (open) skimmer off at the valve (if present), or plug the hole. You will probably be able to find a skimmer plate or plug suitable for the skimmer you pool uses.

How do you winterize a aqua genie?

1. Remove the orifice plate and gasket.
2. Remove the plug on the front of the pump.
3. Insert a quick disconnect fitting for an air compressor.
4. Close the valve for the Aqua Genie.
5. Charge system with 20 lbs of air pressure.
6. Open valve.
7. Repeat several times until all water is out.

What is a pool skimmer?

Pool skimmers are small-to-medium-sized openings built into the side of an in-ground pool. It sucks in pool water, cleans it, then pushes the filtered water back out into the pool.

Do you turn the main drain off when vacuuming a pool?

TO VACUUM THE POOL If your hose has a swivel cuff at one end, that end MUST be on the vac head or you will lose prime. Turn the bottom drain off (ball valve should be in the horizontal position). The ball valve will be found in front of the pump.

Should you backwash pool before vacuuming?

Yes, we recommend backwashing after you vacuum your pool. This allows the filter to shoot out any dirt / debris you have vacuumed up. Don’t forget to set your filter to “rinse” for 30 seconds after backwashing!

What is a weir in a pool?

A weir is a type of barrier across a river that is created to adjust or alter its flow. With this in mind, a weir for a swimming pool is a barrier in a skimmer over which water flows. A floating weir raises and lowers its level to match the water level in a pool or spa.

What are the two holes in a skimmer?

The skimmer sits at the waterline and catches leaves, bugs and trash so they do not clog the filter. Skimmers with a second hole help keep the pump from running dry if the water level is unstable.

What is overflow pool?

Filters. A type of swimming pool or reflecting pool that has at least one edge over which water overflows, creating a dramatic visual effect. noun.

Article first time published on

What is an infinity pool?

: a pool (typically a swimming pool) with an edge over which water flows to give the appearance of the water extending to the horizon And most importantly, the pool and bar are open for business, where a spacious infinity pool looks down on Kalakaua Avenue and makes for the ideal spot to watch the sunset and sip a …

What is drain at bottom of pool for?

Swimming pool main drains are one of two mechanisms used in many pools to circulate and filter their water, the other being skimmers. … A swimming pool main drain uses suction to pull pool water through it. Heavy particulate matter that sinks to a pool’s bottom is often sucked away through a main drain.

Where should a pool skimmer be placed?

A skimmer should be placed in the path of circulating water. There aren’t any hard rules on location, especially with the popularity of free form pools.

Where does the pool skimmer go?

Most skimmers on in-ground pools are built into its upper sides, where the suction draws debris and traps it. Most pool skimmers are accessed via the pool deck area through a trap door or hatch. The skimmer is also in a convenient location to attach a suction line for a pool vacuum.

What is the difference between backwash and waste?

Drain/Waste: Opting the drain or waste setting will remove pool water without forcing it through the filter. Backwash: This clears out any debris, dirt and other contaminants that may have accumulated on the filter.

Do you remove skimmer basket when vacuuming pool?

Now, here answers the question earlier: do you leave skimmer basket in when vacuuming pool? YES, you need to remove the skimmer or strainer basket before attaching the open end of the hose to the inlet. Finally, plug the open vacuum hose into the suction port.

How often should you backwash your pool?

“When do we need to backwash?” – It is recommended to backwash your filter once every 4-6 weeks of regular use. Additionally, there are several instances that would require backwashing in between the normal monthly backwashing.

What is backwashing a pool?

Backwashing is a pool term used to describe a filter cleaning method which reverses the flow of water through your filter system. … The process of backwashing dislodges trapped debris and contaminants, flushing them out through your value’s waste line or a hose that is connected to the pool pump.

What does recirculate mean on pool pump?

The recirculate setting on a swimming pool filter is actually used to bypass the filter mechanism. Recirculate allows the water to flow out of the pool and back into it again without running through the sand or diatomaceous earth in the filtration system.

How much suction should a pool skimmer have?

You should aim for a water level about 1/2 to 2/3 up the opening of the skimmer. Too low and you start to get gurgling sounds which are telling you that your pump is working way too hard at trying to keep the water flowing.

Should I Use main drain or skimmer?

Skimmer Vs. Drain. If the pool receives a lot of leaves and other debris, more suction may be required at the skimmer than the main drain to adequately strain debris floating on the surface. Conversely, if dirt on the bottom of the pool is the principal contaminant, more suction is required at the main drain.

Where is a pool weir?

The weir: the weir is the swinging flap located inside the skimmer mouth and will pivot with the flow of the water. The main purpose of the weir is to prevent the debris from escaping back into the pool.

What is the difference between a dam and a weir?

Dams: A dam is a big wall constructed across a valley to control the flow or raise the level of water held within a catchment area. … A weir is a steel or concrete barrier constructed across a river or creek that regulates water flow and allows water to be slowly released to users downstream.

What is a knife edge pool?

The water spills over the knife edge into a slot right at the top inside edge of the coping or decking material collecting into a collection gutter hidden from view. … The end result is a very sleek, sophisticated looking pool.

What's a zero edge pool?

Zero edge pools, commonly known as infinity pools, have been the trend in the leisure sector for decades. … Typically, an infinity pool design will merge the body of water with the horizon. This is done by allowing the water to spill over the edge into a collection trough that filters and recycles the water.

What are flush walls in a pool?

In flush or zero edge pools, the water reaches the limit of the wall, flushes with the edge beyond, before falling by gravity into a small slot and reaching the overflow tank. This achieves a clean and modern visual effect. It is also possible to customize the edge by choosing different materials for its building.

Are infinity pools expensive?

On average, infinity pools cost $80,000, but the price can range dramatically depending on its size and shape. Infinity pools can cost between $55,000 and $130,000 in all. As the pool’s size increases, pool prices increase as well. Typically, infinity pools will cost about $80 per square foot.

How deep is the infinity pool?

The Sands SkyPark infinity pool is 1.2m deep.

Can I put chlorine tablet in skimmer?

Never put chlorine tablets into the skimmer baskets of your pool. … High levels of chlorine close to the pool pump, pool filter, and pool heater can damage the equipment. The pool heater is especially susceptible to having the copper in the heater get into the pool and ruin the pool plaster.

What is the black stuff in my pool skimmer?

Yet I continue to find a sticky, oily black substance that rings the inside of both skimmers every week or so. … Answer: Simple “problem” with a simple solution: Human oils and suntan lotion are being pulled into the skimmer and then slowly attaching to the sides.

Why does my skimmer basket float?

Look for excessive air in the pump or a lot of air in the filter when you open the air bleed at the top. As for the basket floating, just use a rock to keep it down. The ‘flying saucer’ is to protect your plumbing in case your water level gets too low.